DIY TUB INSTALLATION.

DIY Tub Installation.

DIY Tub Installation.

Blog Article

Detail

What are your beliefs on Tools You Need to Install a New Bathtub ?


Installing A Bathtub
Installing a bath tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is also a reasonably hard job. If the old tub is conveniently obtainable, the job can move speedily; if you need to open a wall to get rid of the old bathtub and place the brand-new bathtub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to move out the old bathtub and embeded in the new one. Make sure you have actually qualified on your own for the task and fit attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This short article will help you mount a new bath tub in your restroom if you have actually already bought a new bathtub as well as do not need to transform the plan of your previous water pipes.
Your devices and product checklist must consist of the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with new ones as a part of your installment, then the first thing you must do is disconnect the supply of water. After doing so, activate the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be fairly problematic because of the limited access that is typically the instance.
    Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
    Prior to going on to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipelines.
    If you require to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next, position the tap in the installing hole in the bath/basin making sure that the washers are in location between the tap as well as the sink. Protect the tap in place with the maker supplied backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The previous kind must be linked to the faucet ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Installing the Bathtub


    Using both wood boards under its feet, put the tub in the required position. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
    The next objective is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the tub until the level reviews level.
    To install faucets, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
    Switch on the water as well as check all joints and also brand-new pipework for leaks and tighten them if needed. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
    Finally, take care of the bath paneling as defined in the maker's user's manual. Tiling as well as sealing around the tub ought to wait till the tub has been made use of at least when as this will resolve it right into its final setting.

    Preparing for the Setup


    Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to avoid pressure on the tub.
    Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the supplied washers.
    Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its last position.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
    You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to enable the motion experienced when the bathtub remains in usage. The sealer can split fairly early if you do not think about this motion before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    I hope you enjoyed our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for taking time to read through our article post. Those who liked our article plz make sure you remember to pass it around. Thank you for your time. Please check up our blog back soon.



    Book Service

    Report this page